How to Use Thermochromic Neon Colour-Change Paint

SFXC® Thermochromic Neon Colour-Change Paint is a ready-to-use, water-based acrylic paint that changes from one colour to a bright neon colour when it warms to 28°C (82.4°F). It starts to change a couple of degrees before 28°C, and the original colour comes back as it cools, so the effect can be repeated again and again. Touch it with a warm hand, breathe on it or warm it gently, and watch the colour switch.

It can be brushed, rolled, stamped or screen printed, so it suits artists, makers, designers, printers, and teachers for supervised classroom use.

Data sheetsTechnical Data Sheet (TDS)Safety Data Sheet (SDS)

Not a toy. This is an art and craft material for adults and young people aged 14 and over. Not suitable for children under 14. Keep out of reach of young children.

Test before you start. Results depend on the surface, the method, the equipment and the user's experience, so always try the paint on a small area or offcut of the same material first. The guidance below is given in good faith as a starting point.

1. The colours

Colour below 28°C Colour above 28°C
Purple Neon Pink
Orange Neon Yellow
Green Neon Yellow
Blue Neon Green

All four change at 28°C (Touch & Reveal). The colour is not made to a Pantone reference and can vary slightly from batch to batch, so for a large project, order enough from one batch.

Can I mix the colours, or add white to make a pastel shade? No. Other paints don't change colour at 28°C, so adding them dulls or hides the effect. Use each colour on its own.

2. Choose your surface

  • Paper, card and board: absorbent surfaces give the best results.
  • Canvas and plaster: works well; apply thin, even coats.
  • Fabric: suitable for fabric. If the item will be washed, the paint must be heat-fixed (see section 6). Always test washing on your own fabric first.
  • Foam and other soft materials: test first on an offcut.
  • Smooth, non-absorbent surfaces (glass, ceramic, metal, glazed pots, most plastics): the standard paint may not grip well. We can supply a lacquer-based version for these surfaces: please contact us before ordering, with details of your surface and project, so we can confirm it's suitable.

If you're not sure, start with a small size and test it on the exact material you'll use.

Specifications at a glance

Effect Reversible colour-to-neon change at 28°C (82.4°F), starting a couple of degrees before
Type Water-based acrylic thermochromic paint, ready to use
Application Brush, roller, stamp or screen
Coverage About 50 ml per square metre per coat
Drying Air dry, or speed up with a hair dryer on a low setting
Heat-fixing (fabric) 150°C for 2 minutes as a starting point; test first. Keep heat brief: longer or hotter heat weakens the colour change
Light fastness Not for long outdoor or strong-sunlight exposure
Thinning Use as supplied
Storage Cool, dark, frost-free, tightly closed
Best used within 6 months
Sizes 100 ml and 1 litre. Sample sizes (under 250 ml) are sent in a resealable pouch.

3. Before you start

  1. Stir the paint well before use, and again from time to time while you work.
  2. Use it as supplied. Don't thin it with alcohol, white spirit or acetone: these damage the colour-change capsules.
  3. Don't mix it with other paints or colours (see section 1).
  4. It is not suitable for spraying. For spraying, use our thermochromic sprayable range.
  5. Make sure the surface is clean, dry and free from dust or grease.

4. Apply in thin, even coats

  • Brush or roller: apply 2–3 thin coats rather than one thick one, letting each coat dry before the next. A small gloss roller gives the most even finish on large areas.
  • Stamp: load the stamp lightly and evenly.
  • Screen printing: print through a screen and squeegee. The best mesh and number of passes depend on your material and design, so run a test print first.
  • Build up coats until you reach the depth of colour you want.

5. Dry gently

  • Leave to air dry, or speed it up with a hair dryer on a low setting, keeping it moving.
  • Don't overheat it. Thermochromic paint reacts to heat by design, and too much heat damages it and weakens the colour change.

6. Fabric that will be washed: heat-fix it

For fabric items that will be washed, fix the dry paint with an iron or heat press.

  • Let the paint dry fully first. Heat and moisture together damage the colour-change capsules, so never fix damp paint and don't use steam.
  • Heat press: 150°C (302°F) for 2 minutes, as a starting point.
  • Iron: dry iron (no steam) on the wool / two-dot setting, kept moving, for about 2 minutes, as a starting point.
  • Keep the heat short. Longer or hotter heat reduces the colour strength and weakens the colour change.
  • Protect the print with a sheet of baking paper when ironing.
  • Test the fixing and a wash on an offcut of your own fabric before a full piece.

Always test first. These settings are a starting point, not a guarantee: fabrics, surfaces and equipment vary, so test the whole process (painting, drying, fixing and washing) on an offcut of the same material before starting a full piece.

7. Test the colour change

Once dry, touch it with a warm hand, breathe on it or use a hair dryer on low, and watch it switch to neon. Let it cool and the original colour returns. Repeat a few times to check it performs the way your piece will be used.

What this paint can't do

  • Long exposure to sunlight. UV light breaks down the colour-change effect and fades neon colours. It isn't suitable for outdoor use.
  • Solvents. Alcohols, white spirit and acetone damage the colour-change capsules.
  • Mixing colours. Mixing it with other paints or with each other weakens the effect.
  • Spraying. It is too thick to spray; use our sprayable range instead.
  • Skin, food or cosmetics. It isn't intended for use on skin, in cosmetics, or on anything that comes into contact with food or the mouth, including toys for young children.

Troubleshooting

  • Weak or dull colour change: usually too much heat during drying or fixing, or the paint has been mixed with another colour or thinned.
  • Patchy colour: coats too thick or uneven. Use thinner coats and a roller for large areas.
  • The effect fades over time: UV light or sunlight. Keep painted items out of strong sunlight.

Caring for painted items

We don't have wash-fastness data for painted fabrics, so test washing on your own fabric first. We recommend a cool, gentle hand or machine wash, inside out. Avoid tumble drying, and don't iron directly over the paint.

Storage, shelf life and cleaning

  • Store in a cool, dark place with the container tightly closed. Protect from frost and from heat.
  • Reseal pouches and bottles straight after use.
  • For best results, use within 6 months.
  • Clean brushes, rollers, stamps and screens with water straight after use.

Handling

The paint is classified as harmful if swallowed and as a skin and eye irritant, and contains a preservative that may produce an allergic reaction. Wear gloves and eye protection, don't eat, drink or smoke while using it, and wash your hands after handling. Keep out of reach of children. Don't pour waste paint down drains. See the Safety Data Sheet for full details.

Moving from testing to production

We supply artists, makers, printers, schools (for supervised classroom use) and businesses worldwide. Our smaller sizes are designed for testing; once you're happy with the result, the paint is available in 1 litre, with larger quantities on request. Contact us with your project and quantities and we'll confirm suitability and lead time.

Our team has over 20 years' experience with colour-changing materials, including supplying the inks for, and technical guidance on, a colour-changing floor installation at Tate Modern.

Before use: please read the Technical Data Sheet (TDS) and Safety Data Sheet (SDS), and always test on your own material first.
See TDS information (Revision 1, November 2026) | See SDS information (Version 1.0.0, November 2026)

Shop thermochromic neon colour-change paint →